
This tutorial will go through the process of replacing the screen of Unihertz Atom XL smartphone.
It is important that you read the entire guide and make sure you can complete all the steps before you start to replace the screen of your Unihertz Atom XL smartphone. Otherwise, finding a local trained repair specialist to conduct the repair is recommended.
How to Replace the Screen for Unihertz Atom XL
How to Replace the Screen for Unihertz Atom XL Step by Step
![]() |
Step 1Remove the 6 screws from the side edge bezel, remove the side edge bezel and take out the SIM card tray gently. |
![]() |
Step 2Remove the ten screws from the rear panel. |
![]() |
Step 3Remove the rear panel assembly. |
![]() |
Step 4Remove the four screws on the antenna module. |
![]() |
Step 5Remove the antenna module. |
![]() |
Step 6Remove the seven screws on the dmr-006 Intercom module. |
![]() |
Step 7Remove the five cable interfaces on the dmr-006 Intercom module. |
![]() |
Step 8Remove the dmr-006 Intercom module. |
![]() |
Step 9Remove the two brackets. |
![]() |
Step 10Remove the six screws on the motherboard. |
![]() |
Step 11Remove the motherboard. (Note: the motherboard is connected with the front panel by a cable, turn the motherboard over and remove the cable interface.) |
![]() |
Step 12Tear off the protective film of the battery adhesive strip from the black part and gently pull it outward. |
![]() |
Step 13Remove the original battery. |
![]() |
Step 14Remove the five screws and the fixing bracket on the digital mic. |
![]() |
Step 15Remove a connector on the digital mic. |
![]() |
Step 16Remove the digital mic. (Note: be careful not to break the cable on the side.) |
![]() |
Step 17Take out the replacement front panel assembly. (Note: pay attention to check whether the black waterproof accessories at the SIM card slot are in good condition.) |
![]() |
Step 18Remove the distance sensor assembly from the original front panel assembly. (Note: please remove the sealing ring beside it together.) |
![]() |
Step 19Install the distance sensor assembly and seal to the replacement front panel assembly. |
![]() |
Step 20Move the lower sealing ring from the original front panel assembly to the replacement front panel assembly. |
![]() |
Step 21Take out the camera protection foam on the replacement front panel assembly. |
![]() |
Step 22First plug the cable interface on the back of the motherboard and then install the motherboard. |
![]() |
Step 23Install the five screws on the motherboard.(Note: the screws marked will be installed later.) |
![]() |
Step 24Install the digital mic, arrange the side cables and plug them in firmly. |
![]() |
Step 25Install the fixing bracket and five screws on the digital mic. |
![]() |
Step 26Install the remaining motherboard screw. |
![]() |
Step 27Affix the battery adhesive strip to the marked position on the back of the battery and tear off the protective film from it after sticking. |
![]() |
Step 28Fasten the battery cable interface and fix the battery. |
![]() |
Step 29Install the cable interface above the battery. |
![]() |
Step 30Install two brackets. |
![]() |
Step 31Install the dmr-006 Intercom module and fasten the cable interface. |
![]() |
Step 32Install the seven screws on the dmr-006 Intercom module. |
![]() |
Step 33Install the antenna assembly and install the four screws on the antenna assembly. |
![]() |
Step 34Install the rear panel assembly. |
![]() |
Step 35Tighten the ten screws on the rear panel assembly. |
![]() |
Step 36Install the SIM card tray, install the side edge bezel, and tighten the six screws on it. |
Step 1Remove the 6 screws from the side edge bezel, remove the side edge bezel and take out the SIM card tray gently. |
![]() |
Step 2Remove the ten screws from the rear panel. |
![]() |
Step 3Remove the rear panel assembly. |
![]() |
Step 4Remove the four screws on the antenna module. |
![]() |
Step 5Remove the antenna module. |
![]() |
Step 6Remove the seven screws on the dmr-006 Intercom module. |
![]() |
Step 7Remove the five cable interfaces on the dmr-006 Intercom module. |
![]() |
Step 8Remove the dmr-006 Intercom module. |
![]() |
Step 9Remove the two brackets. |
![]() |
Step 10Remove the six screws on the motherboard. |
![]() |
Step 11Remove the motherboard. (Note: the motherboard is connected with the front panel by a cable, turn the motherboard over and remove the cable interface.) |
![]() |
Step 12Tear off the protective film of the battery adhesive strip from the black part and gently pull it outward. |
![]() |
Step 13Remove the original battery. |
![]() |
Step 14Remove the five screws and the fixing bracket on the digital mic. |
![]() |
Step 15Remove a connector on the digital mic. |
![]() |
Step 16Remove the digital mic. (Note: be careful not to break the cable on the side.) |
![]() |
Step 17Take out the replacement front panel assembly. (Note: pay attention to check whether the black waterproof accessories at the SIM card slot are in good condition.) |
![]() |
Step 18Remove the distance sensor assembly from the original front panel assembly. (Note: please remove the sealing ring beside it together.) |
![]() |
Step 19Install the distance sensor assembly and seal to the replacement front panel assembly. |
![]() |
Step 20Move the lower sealing ring from the original front panel assembly to the replacement front panel assembly. |
![]() |
Step 21Take out the camera protection foam on the replacement front panel assembly. |
![]() |
Step 22First plug the cable interface on the back of the motherboard and then install the motherboard. |
![]() |
Step 23Install the five screws on the motherboard.(Note: the screws marked will be installed later.) |
![]() |
Step 24Install the digital mic, arrange the side cables and plug them in firmly. |
![]() |
Step 25Install the fixing bracket and five screws on the digital mic. |
![]() |
Step 26Install the remaining motherboard screw. |
![]() |
Step 27Affix the battery adhesive strip to the marked position on the back of the battery and tear off the protective film from it after sticking. |
![]() |
Step 28Fasten the battery cable interface and fix the battery. |
![]() |
Step 29Install the cable interface above the battery. |
![]() |
Step 30Install two brackets. |
![]() |
Step 31Install the dmr-006 Intercom module and fasten the cable interface. |
![]() |
Step 32Install the dmr-006 Intercom module and fasten the cable interface. |
![]() |
Step 33Install the antenna assembly and install the four screws on the antenna assembly. |
![]() |
Step 34Install the rear panel assembly. |
![]() |
Step 35Tighten the ten screws on the rear panel assembly. |
![]() |
Step 36Install the SIM card tray, install the side edge bezel, and tighten the six screws on it. |
![]() |